Samsung Galaxy Note II Motherboard Replacement

View previous topic View next topic Go down

Samsung Galaxy Note II Motherboard Replacement

Post  THE GIVEAWAY BLOG!! on Thu Apr 09, 2015 8:04 am

Sections
Stylus 1 step
Rear Case 2 steps
MicroSD Card 1 step
Battery 2 steps
Midframe 8 steps
Motherboard Assembly 5 steps
Rear Facing Camera Assembly 2 steps
Tools
Plastic Opening Tools Buy it
Phillips #00 Screwdriver Buy it
Buy these parts and tools
Tools (continued)
Spudger Buy it
Tweezers Buy it
Relevant Parts
Samsung Galaxy Note II 2 Motherboard (ATT) Buy it
Samsung Galaxy Note II 2 Motherboard (Verizon) Buy it
Samsung Galaxy Note II 2 Motherboard (Sprint)

Step 1 — Stylus
Grasp the end of the stylus and remove it from its slot in the midframe.
Image #1

EditStep 2 — Rear Case
Pry with a plastic opening tool, or your fingernail, in the divot to the left of the rear-facing camera, near the power button.
Image #1

EditStep 3
Lift the rear case by the corner nearest the divot and remove it from the phone.
Image #1

EditStep 4 — MicroSD Card
If you have an SD card inserted, use the flat end of a spudger, or your fingernail, to press the microSD card slightly deeper into its slot until you hear a click.
After the click, release the card and it will pop out of its slot.
Remove the microSD card.
For reassembly, push the microSD card into the slot until it clicks in place.
Image #1

EditStep 5 — Battery
Insert a plastic opening tool, or your finger, into the notch of the battery compartment and lift the battery upward.
Image #1
EditStep 6
Remove the battery from the midframe.
Image #1
1 EditStep 7 — Midframe
Remove the eleven 4.0 mm Phillips #00 screws securing the midframe to the display assembly.
Image #1

EditStep 8
Insert your plastic opening tool between the midframe and front panel assembly on the side of the phone.
Slide the plastic opening tool down the seam.
Image #1

EditStep 9
Continue to run the plastic opening tool down the seam.
Image #1

EditStep 10
Carefully pry around the corner with a plastic opening tool.
Image #1

EditStep 11
Pry along the top of the phone with a plastic opening tool.
Image #1

EditStep 12
Push the plastic opening tool down to free the corner of the midframe from the display assembly.
Image #1

1 EditStep 13
Free the clips along the power button side of the phone.
Lastly, there are two clips along the top and bottom edge of battery compartment that also hold the display assembly in place.
Gently lift the clips with the spudger.
The display assembly should pop out from the frame.
Image #1

1 EditStep 14
Lift the display assembly out of the midframe.
Image #1

2 EditStep 15 — Motherboard Assembly
Use a spudger to disconnect the vibrator/power button assembly cable connector.
Disconnect the antenna cable connector.
Disconnect the display cable connector.
Image #1

EditStep 16
Disconnect the front-facing camera cable connector.
Disconnect the headphone jack cable connector.
Disconnect the digitizer cable connector.
Image #1

EditStep 17
Use the spudger to disconnect the antenna cable connector from the motherboard.
Disconnect the soft button cable connector.
Disconnect the USB board cable connector.
Image #1
EditStep 18
Remove the 3 mm Phillips #00 screw securing the motherboard to the display assembly.
Image #1

EditStep 19
Gently remove the motherboard.
Hold the motherboard by its edges to prevent ESD damage. Be careful not to snag it on any cables as you extract it from the display assembly.
View Original
Image metadata
Image #1
EditStep 20 — Rear Facing Camera Assembly
Use a spudger to disconnect the rear-facing camera assembly cable connector.
Image #1
EditStep 21
Use tweezers, or your fingers, to remove the rear-facing camera assembly.
avatar
THE GIVEAWAY BLOG!!
Admin

Posts : 161
Join date : 2012-06-11
Age : 28
Location : Malaysia

View user profile http://thousandgiveaway.blogspot.com

Back to top Go down

View previous topic View next topic Back to top

- Similar topics

 
Permissions in this forum:
You cannot reply to topics in this forum